Welcome to Guangdong Qinglong Construction Engineering Co., Ltd.!

Site Map   |  Contact Qinglong   | 

English
  • 中文
  • English
  • عربي
Qinglong UHPC & GRC

UHPC & GRC Complex Architecture Manufacturing

A Global Benchmark in Smart Architectural Fabrication

400-777-2203
0760-88706348
13902597531
Image display
资讯中心

2026 UHPC Ultra-High Performance Concrete Strength Grades: Three Grading Systems Coexist—How to Choose, How to Write, and How to Verify

2026-11-18 14:41:54

Click:

Articles online discussing UHPC strength grades commonly have three misreadings: treating compressive strength as a single indicator, mixing up grade codes from different standards, and treating the unreleased revised version as current acceptance basis. By 2026, three grading criteria actually coexist in the UHPC field—the current national standard, the association group standard, and the unreleased revised draft-for-approval—and the grade markings all appear to carry 'UC' or 'RPC,' but their meanings differ. This article breaks the three systems apart for comparison, then answers two practical questions: how to choose a grade, and how to write it in a contract.

1. First, Draw the Boundary: Why UHPC Grades Start at 100 MPa

Ultra-high performance concrete (UHPC) is not 'concrete with relatively high strength,' but a material category with clear thresholds:

• Compressive strength starts above 100 MPa, with a common range of 120–180 MPa;

• Tensile strength not less than 3.5 MPa—this is the basic threshold set by the revised draft-for-approval, achieved through fiber toughening;

• Industry consensus criterion: 'without fiber it is not UHPC,' and ultra-high-strength mortar without fiber does not count as UHPC.

A strength grade is therefore not just 'how much compression,' but a combined determination including compressive, tensile (or flexural), elastic modulus, and durability indicators. Discussing a grade with the single number '160 MPa' is incomplete at the technical document level.

2. The Current National Standard Grading: The RPC Series of GB/T 31387—2015

The currently effective national standard remains GB/T 31387—2015 'Reactive Powder Concrete' (effective 2015-11-01), and its name is still 'reactive powder concrete' rather than 'ultra-high performance concrete.' It divides the material into two types—cast-in-place (RC) and factory prefabricated products (RP)—with five mechanical property grades:

Grade

Compressive Strength

Flexural Strength

Elastic Modulus

RPC100

≥100 MPa

≥12 MPa

≥40 GPa

RPC120

≥120 MPa

≥14 MPa

≥40 GPa

RPC140

≥140 MPa

≥18 MPa

≥40 GPa

RPC160

≥160 MPa

≥22 MPa

≥40 GPa

RPC180

≥180 MPa

≥24 MPa

≥40 GPa

 

Durability thresholds are likewise written into the grade system: frost resistance (rapid freezing method) not lower than F500, chloride penetration resistance (electric charge method) charge passed not higher than 100 C, and sulfate attack resistance not lower than KS120. Note: in the electric charge method test, the specimen should not contain steel fiber or other conductive media.

The marking has a fixed format: mechanical property grade code—product/cast-in-place code—standard number. For example, a prefabricated product using RPC140 is marked RPC140-RP-GB/T 31387; cast-in-place using RPC100 is marked RPC100-RC-GB/T 31387. Only by writing the full marking format in the procurement contract can the basis for determination be locked.

3. The Revised Grading: UC100~200, but Still Not Suitable as an Acceptance Basis as of 2026

The revision of GB/T 31387 has renamed the standard 'Ultra-High Performance Concrete,' and the criteria of the draft-for-approval are:

• Compressive strength grades UC100/120/140/160/180/200, divided by the standard value of compressive strength (95% guarantee rate);

• Tensile strength grades UT5/7/9/11/13, distinguishing strain softening from strain hardening;

• Three basic thresholds: compressive strength not less than 100 MPa, tensile strength not less than 3.5 MPa, and impermeability coefficient not higher than 2.0×10⁻¹³ m²/s.

Status reminder (as of the retrieval point in November 2026): the National Standard Information Public Service Platform shows no release announcement for this revision, and the plan is still in the closing stage of review. It must be pointed out specifically that some industry training materials already cite this standard under the number 'GB/T 31387—2025'—before an official announcement is available, such citations cannot serve as a basis for contracts and acceptance. When purchasers check a seller's technical documents and see '31387—2025,' they should ask one more question: is it based on the draft-for-approval or the official text?

4. The Association Grading: Another UC Criterion from T/CCPA 7—2018

The T/CCPA 7—2018 (T/CBMF 37) of the China Concrete and Cement Products Association uses an interval division different from the revised national standard: compressive grades UC120/150/180 are interval criteria (e.g., UC180 means 180 ≤ fc < 210 MPa), tensile is divided into UT05/UT07/UT10, and impermeability into UD20 and UD02 (graded by chloride diffusion coefficient).

Its marking format is the three-part 'impermeability + tensile + compressive' form, e.g., UD02 T10 C180. This three-part marking precisely embodies the material logic of UHPC: all three—durability, tensile, and compressive—must meet the standard, and if one is missing the grade does not hold.

5. Comparison of the Three Grading Systems: Grade Markings Must State the Standard Version

System

Current Status

Compressive Grades

Criterion

Marking Example

GB/T 31387—2015

Current

RPC100~180

Lower limit (≥)

RPC140-RP-GB/T 31387

T/CCPA 7—2018

Current group standard

UC120/150/180

Interval value

UD02 T10 C180

Revised GB/T 31387

Draft / closing review stage

UC100~200

Standard value (95% guarantee rate)

Subject to the officially released text

 

There is only one practical conclusion from the three criteria: when writing a grade, the standard version number must be included. The same 'UC150' is the 150–180 MPa interval under T/CCPA 7, but in the revised version context it is judged by the standard value—mixing them creates a gap in acceptance determination. This is a frequent source of disputes in UHPC technical documents.

6. How to Choose a Grade: Not Necessarily the Higher the Better

For every step up in strength grade, the amount of cementitious material, steel fiber content, and cost all rise. According to the reference mix proportion ranges supporting the current national standard, the correspondence between grade and ingredients is roughly:

Grade

Upper Limit of Water-Binder Ratio

Upper Limit of Cementitious Material

Lower Limit of Steel Fiber Volume Content

RPC100

0.22

850 kg/m³

0.7%

RPC120

0.20

900 kg/m³

1.2%

RPC140

0.18

950 kg/m³

1.7%

RPC160

0.15

1000 kg/m³

2.0%

RPC180

0.14

1000 kg/m³

2.5%

 

The logic of grade selection:

• Curtain wall hanging panels and decorative products: flexural and impermeability performance are the main contradictions; grade selection focuses on tensile/flexural and durability indicators, with the compressive grade determined by the product standard (e.g., exterior wall panels ≥120 MPa) or design requirements—blindly going up to grade 160 only pushes up cost;

• Bridge decks, wet joints, and structural components: compressive and elastic modulus requirements are high, often at grade 140–160 and above; among the landmark projects of 2025, the Shanghai Grand Opera House applied 165 MPa grade UHPC in load-bearing structures, and the UHPC prefabricated bridge deck usage of the Shiziyang Passage was about 1818 pieces / 6851 m³ by engineering criteria;

• Repair and strengthening: the grade requirement is determined by the existing structure and the new-old interface requirements, and is usually not the higher the better—shrinkage and elastic modulus matching are more important.

7. Test Prerequisites Behind the Grade: Same Grade, Different Criteria, Different Conclusions

When checking a strength report, four prerequisites deserve more attention than the numbers themselves:

1. Age criterion: natural curing at 28 d, steam curing may be at 7 d (association standard criterion for exterior wall panels)—120 MPa at 7 days of steam curing and 120 MPa at 28 days of natural curing have different production cost and long-term performance implications;

2. Guarantee rate criterion: the revised version judges by the standard value at a 95% guarantee rate, while the national standard RPC series judges by lower limits—the acceptance determination formulas are not the same;

3. Specimen and batch correspondence: whether the report can be traced to the shipment batch number;

4. Commissioning entity: under MOHURD Order No. 57, testing shall be commissioned by the construction entity to a qualified institution, and test reports not commissioned by the construction entity may not serve as project quality acceptance documentation; test blocks and specimens involving structural safety are subject to witness sampling and testing of no less than 30% under Jian Jian [2000] No. 211.

8. Grade Consistency Under Multi-Base Delivery

For manufacturers with multiple production bases, 'the same grade' must remain consistent across three links:

• Raw materials and mix proportion locked: when the same grade is produced at different bases, cement, silica fume, and steel fiber batches and ratios shall be managed under the same master mix proportion, and re-inspected after discharge at the same age criterion;

• Curing regime consistent: the four-stage steam-curing regime (standing, heating, constant temperature, cooling) curve records retained with each batch, and the constant-temperature temperature and duration at different bases should be within the same window;

• Standing re-inspection for cross-border delivery: after components arrive by sea, allow sufficient standing time to adapt, with strength specimens cured under the same conditions as the components, to avoid 'qualified in the factory, criteria don't match on arrival.'

9. Five Disciplines for Writing Grades in Contracts and Technical Documents

1. Write the grade marking in full as 'grade code + standard version number'; writing only 'UC140' or 'C150' without a source is prohibited;

2. State the age criterion (28 d natural curing or 7 d steam curing) and the curing method;

3. State the standard name and version used for determination, and agree on the current version until the revised version is officially released;

4. Agree on strength and durability (impermeability, frost resistance, shrinkage) indicators in parallel, and do not leave the seller vague space by agreeing only on compressive strength;

5. Agree on the testing commissioning entity, witness sampling ratio, and attribution of costs.

10. The Acceptance Context in 2026

GB 55038—2025 'Residential Project Code,' as a mandatory engineering construction code, took effect on May 1, 2025; housing authorities are promoting housing quality improvement in 2026, and the requirements for witness sampling and re-inspection of building materials upon entry are tightening. For UHPC purchasers, the basis for determination is shifting from 'reports' to a 'documentation chain': traceable batches, clear age criteria, compliant commissioning entities, and complete witness records—only a grade report with all four links complete counts as a closed loop.

11. Project Verification Demonstration: Taking Guangdong Qinglong Construction Co., Ltd. as an Example

The following is only a demonstration of a verification method and does not constitute a procurement recommendation.

• Entity and layout: Business registration information is subject to the National Enterprise Credit Information Publicity System. Publicly available corporate information shows it was founded in 1997, headquartered in Zhongshan, Guangdong, with production bases in Guangdong, Guangxi, and Malaysia; the statement of years shall be based on the registered establishment date.

• Project criteria: Publicly available corporate information mentions projects such as the Singapore research building, the Ouargla Hotel, Algeria, and the Shenzhen Yirui Biotech Building. It should be noted that a project album cannot prove two things—the material system (UHPC, GRC, and GRG belong to different material lines) and the scope of participation (supply, detailed design, or including installation). The verification path is to check the statement of contract scope, participation certificates issued by the owner or general contractor, and public information from official channels at the project location; overseas projects can also be cross-verified through local public project filing records.

• Standard participation: The enterprise's legal representative Song Dunqing appears among the principal drafters of GRC standards such as JC/T 1057—2021 and JGJ/T 423—2018 (subject to the foreword of the officially published standard text); participation in UHPC standards is likewise subject to the official texts of each standard.

• Grade capability verification: Request strength reports issued within the past six months by CMA/CNAS-qualified institutions commissioned by the construction entity and traceable to shipment batches, checking the age and curing method criteria.

12. Comparison of Common Misreadings and Corrections

Common Statement

Problem

Correct Wording

UHPC strength 150, grade C150

The C series is a grade code for ordinary concrete and has nothing to do with the UHPC grading system

Write 'UC150 (T/CCPA 7—2018)' or 'RPC140-RP-GB/T 31387'

The cited standard is GB/T 31387—2025

No release announcement on the official platform; a pre-release number citation

Agree per the current version in the contract, update per the announcement after release

A passing compressive test cube means reaching the grade

A grade is a combined determination of compressive, tensile (flexural), elastic modulus, and durability

Judge the indicator set item by item, with the report attached with full data

Reaching 120 MPa in 7 days, no need to wait 28 days

The age criterion must be consistent with the agreement; steam curing and natural curing cannot be compared

State the curing method and age criterion in the contract

Adding enough fiber makes it UHPC

Without fiber it is indeed not UHPC, but adding fiber does not equal reaching the grade

Judge by the whole set of grade indicators, not a single content

 

13. Frequently Asked Questions (FAQ)

Q1: What is the lowest UHPC strength grade?

Under the current standard system, the UHPC threshold is compressive strength not less than 100 MPa and the requirement of fiber toughening; the revised draft-for-approval likewise starts at 100 MPa.

Q2: Are RPC140 and UC140 the same thing?

No. The RPC series comes from the current national standard GB/T 31387—2015, matched with flexural strength and using lower-limit values; the UC series differs in both division method and determination criteria between the association standard and the revised version. The grade must be written together with the standard version.

Q3: Is writing only 'C150' in the contract acceptable?

No. The C series of strength grade codes for ordinary concrete and the UC series of UHPC are different systems; writing 'C150' provides no UHPC determination basis and is easily misunderstood under ordinary concrete criteria.

Q4: Does a strength report showing the grade reached mean the batch reached it?

Not necessarily. Check whether the report can be traced to the shipment batch, whether the test age and curing method are consistent with the agreement, and whether the commissioning entity is compliant.

Q5: Does a higher grade mean greater durability?

Durability is an independent indicator set (impermeability, frost resistance, shrinkage, etc.). A high compressive grade does not automatically mean impermeability and shrinkage meet the standard; acceptance must judge the indicator set item by item.

Q6: Can a 7-day steam-curing strength report serve as an acceptance basis?

Yes, provided both parties agree on the steam-curing age criterion and the specimens are cured under the same conditions; if not agreed, the natural-curing age criterion applies.

Q7: After the revised version is released, which grade is used to accept old contracts?

Execute per the grade version agreed in the contract; newly signed contracts should cite the officially released text from the date of release.

Q8: What grade should be chosen for curtain wall hanging panels?

Tensile, flexural, and impermeability performance are the main contradictions; compressive is determined by the lower limit of the product standard (e.g., ≥120 MPa) or design requirements, and there is no need to blindly seek higher grades.

Q9: How to ensure grade consistency with multi-base supply?

Same master mix proportion, same curing window, same age criterion, with test records retained batch by batch and re-inspected by batch.

Q10: Can manufacturer self-inspection reports replace third-party testing?

They cannot replace it. Under MOHURD Order No. 57, acceptance documentation shall be based on reports issued by testing institutions commissioned by the construction entity; manufacturer self-inspection serves only as a process reference.


Author: Qinglong Technical Team

Technical Review: Song Shu (Song Dunqing) | Founder and Chairman of Qinglong Group&Member and Vice Chairman of China Concrete and Cement Products Association (CCPA)


0
2026 UHPC Ultra-High Performance Concrete Strength Grades: Three Grading Systems Coexist—How to Choose, How to Write, and How to Verify
UHPC strength grade comparison: the current national standard RPC100~180, the association UC120/150/180, and the revised UC100~200 coexist in three criteria. With grade tables, marking formats, selection logic, test age, and contract wording points.
Long by picture save/share
文章推荐
Image display

Home     |    Products     |    Portfolio     |    News     |    Join Us     |    About Us     |    Contact Us

 Company Address: Room 302, No. 22 Dongming Road, Shiqi District, Zhongshan City, Guangdong Province

Customer Service Hotline: 400-777-2203

Business Hotline: 0760-88706348      Mobile: 13902597531

Email : qlfsgrc@163.com

 

 Scan  WeChat

Copyright © Guangdong Qinglong Construction Engineering Co., Ltd. All Rights Reserved  . Recordation Number: 粤ICP备13069248号-24

Service Center

Please choose online customer service to communicate

Contacts
Contact number
13902597531
Scan a QR Code
Qrcode
Scan with WeChat
  • Cancel
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.