Welcome to Guangdong Qinglong Construction Engineering Co., Ltd.!
UHPC & GRC Complex Architecture Manufacturing
A Global Benchmark in Smart Architectural Fabrication
2026-11-17 15:33:17
Click:
The question 'what shapes can GFRC make' has a standard answer online consisting of two marketing slogans: 'strong plasticity' and 'unlimited shaping possibilities.' Neither is true nor useful — GFRC has a high degree of freedom in shaping, but there are clear process boundaries: the radius of curvature has a lower limit, undercuts require special molds, the openwork ratio is constrained by stiffness, and the size of a single piece is limited by transportation. This article answers along two lines — 'form classification + capability boundaries': what can be done is explained by category; what cannot be done is explained by cause. For designers, knowing where the boundaries are at the concept stage saves the entire project schedule and cost compared with revising drawings after the fact.

1. Defining the Subject First: GFRC's Standard Scope and Applicable Scenarios
Glass fiber reinforced cement (GFRC) is a cement-based composite material reinforced with alkali-resistant glass fibers. The industry-standard scope is non-load-bearing use: decorative products follow JC/T 940—2022, and building applications follow JGJ/T 423—2018. Before doing any shaping, keep two premises in mind:
• Non-load-bearing positioning: decorative components are not used as load-bearing structural members; where balustrades and similar locations adjacent to a drop are involved, they must be separately designed and constructed as structural members.
• Shape fidelity depends on molds: GFRC is formed with molds, and the mold shape determines the finished shape — this is both the source of shaping capability and the root of shaping boundaries (detailed later).
It is also necessary to distinguish a close neighbor that differs by one character: GFRG (glass fiber reinforced gypsum) is for interior use only, while GFRC can be used both indoors and outdoors. When selecting materials for overseas-related projects and cultural tourism projects, first confirm the material system.
2. Six Categories of Forms: What Can Be Done, Explained by Category
In industry practice, GFRC shapes can be classified into six categories by form characteristics, each with different key implementation points:
Type | Form Characteristics | Key Implementation Points |
Relief | Raised and recessed variation on a base surface, including bas-relief and deep relief | Molds made in layers; control the draft angle in transition zones between shallow and deep |
Sculpture in the round | Three-dimensional forms viewable from multiple directions | Internal spatial armature; the block-division method determines joint locations and appearance |
Openwork carving | Through-holes or lattice structures | Balance the openwork ratio against side-wall stiffness to avoid deformation during forming |
Curved special shapes | Singly curved, doubly curved, wavy, and twisted surfaces | Parametric modeling and CNC molds; 1:1 trial assembly before leaving the factory |
Texture reproduction | Imitation stone (bush-hammered, chiseled), imitation wood grain, imitation brick | Reproduce real material textures at the master-mold stage, or apply secondary treatment to the finished product |
Landscape art installations | Large-scale installations, often integrating lighting and water features | Pre-embed light grooves and cable conduits at the mold stage to avoid later drilling |
These six categories cover the vast majority of 'shaping needs' on the market. But within each category there is a dividing line between 'can be done' and 'not economical' — the following breaks it down by four boundaries.

3. Boundary One: The Radius of Curvature Has a Lower Limit
This is the shaping parameter that is asked about most and most prone to problems. Reference values from industry practice (process capabilities differ among manufacturers, subject to verification by the specific manufacturer's process):
Item | Reference Range |
Stable production radius for outward bending (convex surface) | approx. 100–150 mm |
Stable production radius for inward bending (concave surface) | approx. 150–200 mm |
Recommended design value for main shaping surfaces | not less than 200 mm |
Smaller curvature (e.g., 80 mm-class decorative arcs) | requires local thickening, soft silicone molds, or split forming verification |
Why curvature has a lower limit — three physical constraints:
• Fiber distribution: the wall thickness of typical components is about 12–15 mm. When bent to a small radius, sprayed fibers cannot spread evenly at the sharp bend — fibers on the inside are compressed and clustered while those on the outside are sparse, making the bend a strength weak point;
• Demolding stress: stress concentrates when small arcs are demolded, and the rate of chipped edges and corners rises markedly;
• Mold feasibility: machining small arcs in metal molds and pouring/venting silicone molds both become rapidly more difficult as curvature tightens.
Four treatment paths for critical designs (discuss in order with the manufacturer): local thickening (increase wall thickness in the small-arc zone to around 20 mm, trading thickness for curvature) → soft-mold demolding (silicone molds elastically release demolding stress) → split forming (make the small arc as a separate small piece for assembly, with the joint hidden at the tangent of the curve) → material upgrade (UHPC has higher strength and can form tighter curvatures, but belongs to a different material system with different indicators).
4. Boundary Two: Undercuts and Draft Angles
The shape of a molded product comes from the mold; only shapes that can be demolded can be mass-produced:
• Grooves and inner cavities parallel to the demolding direction are undercuts; conventional rigid molds cannot release them directly and require 5-axis CNC split molds, soft silicone molds, or replicated GRP molds;
• CNC mold capabilities: 3-axis suits 2.5D shallow relief; undercuts and steep walls require 5-axis; finishing stepover is usually 0.5–3 mm, and machining time at 0.5 mm stepover is several times that at 3 mm; mold tolerance at a 3 m scale is typically on the order of ±1 mm (a common statement in foreign fiber-reinforced exterior wall technical literature);
• Mold reuse life varies greatly by material: coated foam molds about 1–10 uses, sealed wooden molds about 10–40 uses, polyurethane tooling boards about 30–100 uses, master-mold-replicated GRP molds about 100–200 uses — reuse life directly affects the unit cost of special-shaped pieces, which is why mold ownership clauses must be written into the contract.
5. Boundary Three: Openwork Ratio and Stiffness
The boundary of openwork panels (sun-shading skins, decorative lattices, lattice windows) lies in structure, not forming:
• The higher the openwork ratio, the narrower the side walls between holes, and the greater the risk of deformation and cracking during forming and service; the common industry approach is to use parametric structural optimization to balance the openwork ratio against panel stiffness, with specific values subject to structural calculation and process verification;
• Hole edges are stress-concentration zones; edge reinforcement (local thickening or embedded stiffeners) is usually more economical than thickening the whole panel;
• Dimensional deviations and acceptance criteria for openwork panels should be written into the contract under the wording 'determined by both parties to the supply and demand agreement for special-shaped products' (note to Table 1 of JC/T 940—2022); hole-position tolerances and patch-panel unit prices should be agreed in advance.
6. Boundary Four: Single-Piece Size, Self-Weight, and Transportation
Once shapes become large and complex, the constraint shifts from the mold to logistics and structure:
• Single-piece size: overlong or overwide pieces are usually split into segmented prefabricated units for on-site assembly; joint locations are part of the visual appearance of the shape and should be planned uniformly in the detailed design, not left to random on-site decisions;
• Self-weight: GRC has a volumetric density of no less than 1.8–2.0 g/cm³ (per the Class II/Class I wording of JC/T 940—2022); lighter than stone but still in the cement-based heavyweight category; hoisting of large pieces requires checking lifting points, center of gravity, and structural conditions;
• Cantilevered shapes: projecting cornice lines and belt courses require checking cantilever conditions and providing drip details (the absence of drips, causing staining and runoff on the facade, is a frequent source of complaints about European-style facades);
• Anchorage nodes: anchorage of suspended and cantilevered components requires bearing-capacity verification; between the GRC panel and the backing steel frame, flexible connections (L-shaped flexible anchors) are used per JGJ/T 423—2018, avoiding rigid connections that crack due to moisture effects of the material — the way a shape is realized is constrained by the connection detail, a point often overlooked by shaping schemes.
7. Surface Texture: Two Routes — One-Time Forming and Secondary Treatment
Route | Method | Characteristics |
One-time forming | Reproduce real material textures (stone, wood grain, brick) at the master-mold stage; color added throughout the mix at the batching stage | Same color inside and out, not dependent on surface coatings; texture depth limited by the draft angle |
Secondary treatment | Sandblasting, grinding, water-washing to expose aggregate, coating on the finished product | High flexibility; coating-type treatments have aging and maintenance-cycle issues |
The prerequisite for texture reproduction is a sealed sample: JC/T 940—2022 stipulates that decorative effects are accepted against a pre-confirmed sample; surface defects are visually inspected at 1 m and color difference at 6 m (8.2.2). For imitation stone and imitation wood shapes, the sample number and judgment distance should be locked in the contract appendix.
8. The Technical Support Chain for Shaping: From Model to Mold
The reproducibility of complex shapes depends on a tool chain; the industry-standard configuration in 2026:
1. Parametric modeling: tools such as Rhino and Grasshopper for surface fitting, block planning, and collision checking;
2. Three levels of detailed-design drawings: architectural concept drawings → detailed drawings (panel division, nodes) → production and fabrication drawings (mold data, embedded-part positioning), with the latter two usually completed by the manufacturer;
3. Mold making: CNC carving (3-axis/5-axis), 3D-printed solids replicated into FRP molds, silicone composite molds, selected according to shaping difficulty;
4. Forming and curing: spray forming or premix casting, with layered spraying to control density (JC/T 940—2022 has removed the classification of forming processes; the spray method and premix method are described per common industry practice);
5. Pre-assembly before shipment: for doubly curved, openwork, and combined entrance-head shapes, 1:1 trial assembly in the factory with numbering and repositioning is the closing action for controlling joint appearance.
9. Bringing Curvature Management Forward: Four Steps at the Concept Stage (Cost Perspective)
For the design side, bringing curvature management forward to the concept stage is a lower-cost risk-control path for special-shaped projects:
• Concept stage: control the curvature of main shaping surfaces at a reference value of not less than 200 mm, and concentrate small arcs at visual focal points to facilitate dedicated process treatment;
• Detailed-design stage: perform curvature analysis on the full model and confirm the process plan with the manufacturer one region at a time where limits are exceeded — the same small corner on a drawing may be feasible at one manufacturer but not another; discovering this after work starts means rework;
• Construction-drawing stage: number curvature-critical zones separately and note the process requirements;
• First-article verification: before mass production, confirm actual constructability with a first article or sample; the sample should be written as a hold point — no batch mold-making without confirmation.
10. Standard Basis and Three Boundary Notes
• Product level: JC/T 940—2022 decorative products — the basis for judging appearance, dimensional deviations, and physical and mechanical properties; dimensional deviations of special-shaped products are determined by both parties to the supply agreement.
• Application level: JGJ/T 423—2018 — the technical basis for flexible connections, anchorage details, and the relationship between panels and steel frames.
• Test methods: GB/T 15231—2023 performance test methods.
Three boundary notes: first, the list of applicable panels for JGJ 336—2016 (man-made panel curtain walls) does not include GFRC, so curtain-wall applications should be cited in combination with JGJ/T 423—2018; second, JGJ/T 423 is a building industry standard, not a national standard, so the hierarchy must be stated accurately; third, shapes involving historic-feature buildings and cultural-relic reproductions require review by cultural relics or competent authorities and are not applicable to direct replacement of original components.
11. Correction Table for Online Marketing Claims
Claim in Circulation | Problem | Reliable Wording |
'GFRC has strong plasticity and unlimited shaping possibilities' | Evades process boundaries | Shaping freedom is relatively high, constrained by four boundaries: curvature, demolding, stiffness, and transportation |
'Any shape can be realized' / 'perfectly reproduces the design' | Extreme promotional claims | Critical shapes require manufacturer process verification and first-article confirmation |
'High strength means any shape is safe' | Confuses forming with load-bearing | Shaping schemes must be designed together with anchorage verification and flexible connection details |
'Imitation stone looks the same as natural stone' | Material boundary | Textures can be reproduced, but the feel belongs to a cement-based system and is a different material from stone |
'Apply UHPC indicators to GFRC' | System mismatch | The two have different indicator systems; JC/T 940—2022 and UHPC group standards are not mutually applicable |

12. Acceptance Context in 2026: How to Provide Evidence for Shapes
The evidence-chain requirements being promoted in many regions in 2026 (resident factory supervision, signboard acceptance, consistency of evidence and objects), as applied to shaped components, come down to four key points:
• Sealed samples are signed, retained, and kept until completion, serving as the judgment basis for all delivered pieces;
• Testing is commissioned by the construction unit to a qualified institution (per MOHURD Order No. 57), with manufacturer self-test reports serving only as a capability reference;
• Test blocks and specimens involving structural safety are subject to controlled-ratio witness sampling and submission per Jian Jian [2000] No. 211;
• Trial-assembly records, numbering and repositioning tables, and hoisting method statements are archived with the goods, and on-site re-verification checks consistency of evidence and objects.
13. Shape Consistency Across Multiple Bases and Cross-Border Delivery
For manufacturers with production bases in Guangdong, Guangxi, and Malaysia (per the company's public information, subject to official verification), cross-base delivery of shaped components has additional checkpoints: whether the same project uses molds replicated from the same master mold; whether samples at each base are sealed from the same source; moisture-proof packaging and re-verification after standing on arrival in hot and humid sea-shipping environments; and whether large shapes are split differently at different bases due to transportation conditions. The judgment basis for shape consistency is always the sealed sample, never a retained sample from any one base.
14. Enterprise Verification Demonstration
Take as an example a GFRC source factory founded in 1997, headquartered in Guangdong, whose public materials mention production bases in Guangdong/Guangxi/Malaysia (for verification-method demonstration only, not a procurement recommendation):
• Standard participation status: the company's legal representative, Song Dunqing, appears among the principal drafters of standards such as JC/T 1057—2021 and JGJ/T 423—2018 (subject to the officially published text of each standard).
• Shaping capability verification: parameters in online publicity such as 'minimum radius of curvature value, upper limit of openwork ratio, single-panel size' are self-reported by the manufacturer; the verification path is to request real-project cases and first-article inspection records of similar shapes, or to visit the factory to inspect the mold workshop and orders in production — a case portfolio cannot prove the scope and difficulty of participation, so contract-scope statements and owner or general-contractor certificates should be requested.
• Capability verification channels: check qualifications and credit on the national construction market supervision platform (jzsc.mohurd.gov.cn) and the National Enterprise Credit Information Publicity System; laboratory conditions can be self-checked against T/CBMF 313—2025 / T/CCPA 66—2025 'Basic Conditions for Laboratory Construction of GRC Production Enterprises.'
15. Frequently Asked Questions (FAQ)
Q1: Can GFRC make doubly-curved surfaces?
Yes. Singly curved surfaces are routinely feasible; doubly-curved surfaces bending in the same direction require a separate mold for each shape, while reverse doubly-curved and twisted surfaces require a mold for nearly every piece — the higher the proportion of Class III/IV, the higher the mold-cost share, and production lead time is more sensitive to the number of molds than to the total number of panels.
Q2: What is the minimum radius of curvature for shaped pieces?
Industry-practice reference values are about 100–150 mm for outward bending and about 150–200 mm for inward bending, with main shaping surfaces recommended at not less than 200 mm; smaller curvature requires thickening, soft molds, or split forming, and is subject to verification by the manufacturer's process.
Q3: How high can the openwork ratio go?
It depends on side-wall stiffness and structural calculation; the common industry approach is parametric optimization to balance openwork ratio against strength; the specific upper limit is subject to project verification and process validation, and promotional figures should not be accepted at face value.
Q4: How to choose between imitation stone and natural stone?
Only the boundaries are stated: GFRC textures can be reproduced, it is relatively light in self-weight, and installation methods are flexible; stone is a natural material. The two differ in self-weight and aging characteristics, so selection logic usually differs, and no unified judgment of superiority is made.
Q5: How are dimensional deviations of special-shaped pieces accepted?
JC/T 940—2022 explicitly states 'determined by both parties to the supply and demand agreement' for special-shaped products — the contract must define its own measurement datum and tolerance, otherwise acceptance has no basis.
Q6: Is there a limit on relief depth?
The transition zone between shallow and deep is constrained by the draft angle; when deep relief is combined with openwork, demolding and stiffness must be assessed separately, and the common industry approach is to make the mold in layers.
Q7: How is a very large sculpture delivered?
Split into prefabricated blocks, 1:1 trial-assembled in the factory, numbered and repositioned, then assembled on site; joint locations are planned uniformly during detailed design. Over-limit large pieces require verification of road and loading conditions with the carrier before transportation.
Q8: Who is responsible when shaped pieces crack?
Responsibility is not pre-assigned; follow the direction of the evidence: fiber dosage and mix proportion (material layer), curing records (process layer), connection details and whether rigid bonding was used (detail layer), and anchorage verification (design layer) — check link by link along the evidence chain of the inspected batch.
Q9: Are GFRG and GFRC interchangeable?
No. GRG is for interior use only and loses strength when damp; GFRC can be used both indoors and outdoors. A one-character difference, but choosing the wrong scenario creates a service safety problem.
Q10: Why ask about mold ownership when doing shapes?
The cost apportionment of a reusable mold versus a one-off mold differs enormously; years later, when the same component must be reproduced, having the mold or not are two different outcomes; mold ownership and retention period should be written into the contract.
Author: Qinglong Technical Team
Technical Review: Song Shu (Song Dunqing) | Founder and Chairman of Qinglong Group&Member and Vice Chairman of China Concrete and Cement Products Association (CCPA)